LevelOne WAP-6150 Bedienungsanleitung Seite 1

LevelOne User Manual WAP-6150 300Mbps Wireless Gigabit PoE Access Point

10 1.2.5 Button Indicators Button Description WEC(Wireless Easy Connection) The device has to take about 36 sec to change Mode completely. Step1:Pre

11 Chapter 2 Getting Started Please use windows EZ setup utility or Web UI wizard to enter the setup process. 2.1 Easy Setup by Configuring Web

12 Select “Wizard” for basic settings in a simple way. Or, you can go to Basic Network / Advanced Network / Applications / System to setup the configu

13 Step 2 Entry LAN IP Address. Step 3-1 Wireless setting. Step 3-2 Wireless authentication and encryption. Step 4 Check the infor

14 Step 5 System is applying the setting. Step 6 Click finish to complete it.

15 2.2 Use WEC Button to Setup Wireless Profiles WEC Button is Wireless Easy Connection. There are 2 purposes for this Button. One is to switch AP in

16 Configure Slave AP via WEC Button Step 1 Check 2.4GHz LED of Access Point which acts as Master Mode. It should be Green. If not, please use WEC

17 Chapter 3 Making Configurations Whenever you want to configure your network or this device, you can access the Configuration Menu by

18 Afterwards, you can go Wizard, Basic Network, Advanced Network, Application or System respectively on left hand side of web page. Note: You ca

19 3.1 Basic Network You can enter Basic Network for Ethernet LAN and Wireless settings as the icon here shown 3.1.1 Ethernet LAN This device su

2 TABLE OF CONTENTS CHAPTER 1 INTRODUCTION ...

20 3.1.2 Wireless Wireless settings allow you to set the WLAN (WiFi) configuration items. When the wireless configuration is done your WiFi LAN is re

21 1. Wireless Module: Enable the wireless function. 2. Wireless Operation Mode: Choose “AP Only Mode” from the list. 3. Green AP: Enable the G

22 7. VLAN ID: Supports mapping of SSIDs to VLANs to separate workgroups across wireless and wired domains. 8. Max Supported Stations: Support Max S

23 1. Lazy Mode: This device support the Lazy Mode to automatically learn the MAC address of WDS peers, you don’t have to input other peer AP's

24 default setting is “A/N mixed”. 10. Authentication & Encryption: You may select one of the following authentications to secure your w

25 However, not all the APs can be set to enable the Lazy mode simultaneously; at least there must be one AP with all the WDS peers’ MAC address fille

26 1. Green AP: Enable the Green AP function to reduce the power consumption when there is no wireless traffics. 2. Network ID (SSID): Network ID

27 1. Beacon interval: Beacons are packets sent by a wireless router to synchronize wireless devices. 2. Transmit Power: Normally the wireless tran

28 1. Beacon interval: Beacons are packets sent by a wireless router to synchronize wireless devices. 2. Transmit Power: Normally the wireless tran

29 3.1.3 IPv6 The growth of the Internet has created a need for more addresses than are possible with IPv4. IPv6 (Internet Protocol version 6) is a v

3 3.3.2.3 Email Alert ...

30 3.2 Advanced Network This router also supports many advanced network features, such as Firewall, and Management. You can finish those

31 Afterwards, click on “Save” to store your settings or click “Undo” to give up the changes. 3.2.2 Management 3.2.2.1 UPNP UPnP Intern

32 1. Enable SNMP: Enable this Function. 2. SNMP Version: Supports SNMP V1, V2c, and V3. 3. Get Community: The community of GetRequest that this

33 “authPriv” for both authentication and private key required. 8. Username 1/2: Use this field to identify the user name for the specified level of

34 3.3 System In this section you can see system information, system logs, use system tools for system update and do service scheduling and system ad

35 1. Log Types: You can select the log types to be collected in the web log area. There are “System”, “Attacks”, “Drop”, and “Debug” types for you

36 This device can also export system logs via sending emails to specific recipients. The items you have to setup include: 1. Setting of Email ale

37 click “Undo” to give up the changes. 3.3.3.2 FW Upgrade If new firmware is available, you can upgrade router firmware through the WEB GUI here.

38 3.3.3.3 System Time If new firmware is available, you can upgrade router firmware through the WEB GUI here. 1. Time Zone: Select a time zone whe

39 3.3.3.4 Others In this section you can do system backup, reset to default, system reboot settings and ping test. 1. Backup Setting: You can backu

4 Copyright The contents of this publication may not be reproduced in any part or as a whole, stored, transcribed in an information retrieval system,

40 3.3.4 MMI 3.3.4.1 Web UI You can set UI administration time-out duration give remote administration host port in this page. When the host port is

41 CHAPTOR 4 Troubleshooting This Chapter provides solutions to problems for the installation and operation of the WiFi Concurrent N600 Business AP

42 properly. Network adapter names will vary depending on your specific adapter. The installation steps listed below are applicable for all network ad

43 III. Disable all security settings such as WEP, and MAC Address Control. IV. Turn off the WiFi Concurrent N600 Business AP and the client, then r

44 II. Try changing the channel on the WiFi Concurrent N600 Business AP, and your Access Point and Wireless adapter to a different channel t

45 Appendix A. Licensing information This product includes copyrighted third-party software licensed under the terms of the GNU General Public Licens

46 GNU GENERAL PUBLIC LICENSE Version 2, June 1991 Copyright (C) 1989, 1991 Free Software Foundation, Inc. 59 Temple Place, Suite 330, Boston, MA

47 1. You may copy and distribute verbatim copies of the Program's source code as you receive it, in any medium, provided that you conspicuously

48 offering equivalent access to copy the source code from the same place counts as distribution of the source code, even though third parties are not

49 NO WARRANTY 11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE

5 Chapter 1 Introduction Congratulations on your purchase of this outstanding product: BDP77A-001 WiFi 4G Business Gateway. This device i

6 1.2 Hardware Installation 1.2.1 WARNING 1.2.2 SYSTEM REQUIREMENTS Network Requirements  An Ethernet-based Cable or DSL modem 

7 CD Installation Wizard Requirements  ® ® 

8 1.2.3 Hardware Configuration Rear View: WEC Button Reset Button LAN Port LAN(PoE) Port Power Jack

9 1.2.4 LED Indicators LED Description Status Color: Amber / Green Soild Amber: Device druing power-on process Soild Amber: Device druing power-on